1 files changed, 0 insertions, 137 deletions
diff --git a/man/man3/zmq_setsockopt.3 b/man/man3/zmq_setsockopt.3
deleted file mode 100644
index f1dd9cb..0000000
--- a/man/man3/zmq_setsockopt.3
+++ /dev/null
@@ -1,137 +0,0 @@
-.TH zmq_setsockopt 3 "" "(c)2007-2010 iMatix Corporation" "0MQ User Manuals"
-.SH NAME
-zmq_setsockopt \- sets a specified option on a 0MQ socket
-.SH SYNOPSIS
-.B int zmq_setsockopt (void *s, int option, const void *optval, size_t optvallen); 
-.SH DESCRIPTION
-Sets an option on the socket.
-.IR option
-argument specifies the option from the list below.
-.IR optval
-is a pointer to the value to set,
-.IR optvallen
-is the size of the value in bytes.
-
-.IP "\fBZMQ_HWM\fP"
-High watermark for the message pipes associated with the socket. The water
-mark cannot be exceeded. If the messages don't fit into the pipe emergency
-mechanisms of the particular socket type are used (block, drop etc.) If HWM
-is set to zero, there are no limits for the content of the pipe.
-
-Type: int64_t  Unit: messages  Default: 0
-
-.IP "\fBZMQ_LWM\fP"
-Low watermark makes sense only if high watermark is defined (i.e. is non-zero).
-When the emergency state is reached when messages overflow the pipe, the
-emergency lasts at most till the size of the pipe decreases to low watermark.
-Normal state is resumed at that point.
-
-Type: int64_t  Unit: messages  Default: 0
-
-.IP "\fBZMQ_SWAP\fP"
-Swap allows the pipe to exceed high watermark. However, the data are written
-to the disk rather than held in the memory. Until high watermark is
-exceeded there is no disk activity involved though. The value of the option
-defines maximal size of the swap file.
-
-Type: int64_t  Unit: bytes  Default: 0
-
-.IP "\fBZMQ_AFFINITY\fP"
-Affinity defines which threads in the thread pool will be used to handle
-newly created sockets. This way you can dedicate some of the threads (CPUs)
-to a specific work. Value of 0 means no affinity. Work is distributed
-fairly among the threads in the thread pool. For non-zero values, the lowest
-bit corresponds to the thread 1, second lowest bit to the thread 2 etc.
-Thus, value of 3 means that from now on newly created sockets will handle
-I/O activity exclusively using threads no. 1 and 2.
-
-Type: int64_t  Unit: N/A (bitmap)  Default: 0
-
-.IP "\fBZMQ_IDENTITY\fP"
-Identity of the socket. Identity is important when restarting applications.
-If the socket has no identity, each run of the application is completely
-separated from other runs. However, with identity application reconnects to
-existing infrastructure left by the previous run. Thus it may receive
-messages that were sent in the meantime, it shares pipe limits with the
-previous run etc.
-
-Type: string  Unit: N/A  Default: NULL
-
-.IP "\fBZMQ_SUBSCRIBE\fP"
-Applicable only to ZMQ_SUB socket type. It establishes new message filter.
-When ZMQ_SUB socket is created all the incoming messages are filtered out.
-This option allows you to subscribe for all messages (""), or messages 
-beginning with specific prefix (e.g. "animals.mammals.dogs."). Multiple
-filters can be attached to a single 'sub' socket. In that case message passes
-if it matches at least one of the filters.
-
-Type: string  Unit: N/A  Default: N/A
-
-.IP "\fBZMQ_UNSUBSCRIBE\fP"
-Applicable only to ZMQ_SUB socket type. Removes existing message filter.
-The filter specified must match the string passed to ZMQ_SUBSCRIBE options
-exactly. If there were several instances of the same filter created,
-this options removes only one of them, leaving the rest in place
-and functional.
-
-Type: string  Unit: N/A  Default: N/A
-
-.IP "\fBZMQ_RATE\fP"
-This option applies only to sending side of multicast transports (pgm & udp).
-It specifies maximal outgoing data rate that an individual sender socket
-can send.
-
-Type: uint64_t  Unit: kilobits/second  Default: 100
-
-.IP "\fBZMQ_RECOVERY_IVL\fP"
-This option applies only to multicast transports (pgm & udp). It specifies
-how long can the receiver socket survive when the sender is inaccessible.
-Keep in mind that large recovery intervals at high data rates result in
-very large recovery buffers, meaning that you can easily overload your box
-by setting say 1 minute recovery interval at 1Gb/s rate (requires
-7GB in-memory buffer).
-
-Type: uint64_t Unit: seconds Default: 10 
-
-.IP "\fBZMQ_MCAST_LOOP\fP"
-This option applies only to multicast transports (pgm & udp). Value of 1
-means that the mutlicast packets can be received on the box they were sent
-from. Setting the value to 0 disables the loopback functionality which
-can have negative impact on the performance. If possible, disable
-the loopback in production environments.
-
-Type: uint64_t Unit: N/A (boolean value) Default: 1
-
-.IP "\fBZMQ_SNDBUF\fP"
-Sets the underlying kernel transmit buffer size to the specified size. See
-.IR SO_SNDBUF
-POSIX socket option. Value of zero means leaving the OS default unchanged.
-
-Type: uint64_t Unit: bytes Default: 0
-
-.IP "\fBZMQ_RCVBUF\fP"
-Sets the underlying kernel receive buffer size to the specified size. See
-.IR SO_RCVBUF
-POSIX socket option. Value of zero means leaving the OS default unchanged.
-
-Type: uint64_t Unit: bytes Default: 0
-
-.SH RETURN VALUE
-In case of success the function returns zero. Otherwise it returns -1 and
-sets
-.IR errno
-to the appropriate value.
-.SH ERRORS
-.IP "\fBEINVAL\fP"
-unknown option, a value with incorrect length or invalid value.
-.SH EXAMPLE
-.nf
-int rc = zmq_setsockopt (s, ZMQ_SUBSCRIBE, "", 0);
-assert (rc == 0);
-.fi
-.SH SEE ALSO
-.BR zmq_socket (3)
-.BR zmq (7)
-
-.SH AUTHOR
-Martin Sustrik <sustrik at 250bpm dot com>