zmq_tcp(7) ========== NAME ---- zmq_tcp - 0MQ unicast transport using TCP SYNOPSIS -------- TCP is an ubiquitous, reliable, unicast transport. When connecting distributed applications over a network with 0MQ, using the TCP transport will likely be your first choice. ADDRESSING ---------- A 0MQ address string consists of two parts as follows: 'transport'`://`'endpoint'. The 'transport' part specifies the underlying transport protocol to use, and for the TCP transport shall be set to `tcp`. The meaning of the 'endpoint' part for the TCP transport is defined below. Assigning a local address to a socket ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ When assigning a local address to a socket using _zmq_bind()_ with the 'tcp' transport, the 'endpoint' shall be interpreted as an 'interface' followed by a colon and the TCP port number to use. An 'interface' may be specified by either of the following: * The interface name as defined by the operating system. * The primary IPv4 address assigned to the interface, in it's numeric representation. * The wildcard `*`, meaning that the interface address is unspecified. NOTE: Interface names are not standardised in any way and should be assumed to be arbitrary and platform dependent. On Win32 platforms no short interface names exist, thus only the primary IPv4 address may be used to specify an 'interface'. Connecting a socket ~~~~~~~~~~~~~~~~~~~ When connecting a socket to a peer address using _zmq_connect()_ with the 'tcp' transport, the 'endpoint' shall be interpreted as a 'peer address' followed by a colon and the TCP port number to use. A 'peer address' may be specified by either of the following: * The DNS name of the peer. * The IPv4 address of the peer, in it's numeric representation. WIRE FORMAT ----------- 0MQ messages are transmitted over TCP in frames consisting of an encoded 'payload length', followed by a 'flags' field and the message body. The 'payload length' is defined as the combined length in octets of the message body and the 'flags' field. For frames with a 'payload length' not exceeding 254 octets, the 'payload length' shall be encoded as a single octet. The minimum valid 'payload length' of a frame is 1 octet, thus a 'payload length' of 0 octets is invalid and such frames SHOULD be ignored. For frames with a 'payload length' exceeding 254 octets, the 'payload length' shall be encoded as a single octet with the value `255` followed by the 'payload length' represented as a 64-bit unsigned integer in network byte order. The 'flags' field consists of a single octet reserved for future expansion and MUST be set to `0`. The following ABNF grammar represents a single 'frame': .... frame = (length flags data) length = OCTET / (escape 8OCTET) flags = OCTET escape = %xFF data = *OCTET .... The following diagram illustrates the layout of a frame with a 'payload length' not exceeding 254 octets: .... 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Payload length| Flags | Message body ... | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Message body ... +-+-+-+-+-+-+- ... .... The following diagram illustrates the layout of a frame with a 'payload length' exceeding 254 octets: .... 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0xff | Payload length ... | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Payload length ... | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Payload length| Flags | Message body ... | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Message body ... +-+-+-+-+-+-+-+ ... .... EXAMPLES -------- .Assigning a local address to a socket ---- /* TCP port 5555 on the local loopback interface on all platforms */ rc = zmq_bind(socket, "tcp://127.0.0.1:5555"); assert (rc == 0); /* TCP port 5555 on the first ethernet network interface on Linux */ rc = zmq_bind(socket, "tcp://eth0:5555"); assert (rc == 0); /* TCP port 5555 with an unspecified interface */ rc = zmq_bind(socket, "tcp://*:5555"); assert (rc == 0); ---- .Connecting a socket ---- /* Connecting using an IP address */ rc = zmq_connect(socket, "tcp://192.168.1.1:5555"); assert (rc == 0); /* Connecting using a DNS name */ rc = zmq_connect(socket, "tcp://server1:5555"); assert (rc == 0); ---- SEE ALSO -------- linkzmq:zmq_bind[3] linkzmq:zmq_connect[3] linkzmq:zmq_pgm[7] linkzmq:zmq_ipc[7] linkzmq:zmq_inproc[7] linkzmq:zmq[7] AUTHORS ------- The 0MQ documentation was written by Martin Sustrik and Martin Lucina .